AC Service | 9 Things You Need to Know About Air Conditioning

AC Service | 9 Things You Need to Know About Air Conditioning

AC Service | Keeping your AC in shape will help you stay cool and save dough.

1. Change the filter
 
Why and How to Change Filters
 
Dirty filters kill your AC’s efficiency, so install a new one every month during the cooling season for central and window units (or clean them if you’ve got the washable type). Look for the filter’s minimum efficiency reporting value, or MERV, which ranges from 1 to 12 for home AC units; the higher the number, the better filtration it provides (and the more energy needed to pull air through it, so balance air-quality concerns with energy costs).
 
2. Fix air leaks
 

Why and How to Fix Leaks

Ducts can lose up to 30 percent of airflow through leaks, and window AC units are notoriously tough to seal properly. Find leaks using the old “smoke trick”: For window units, light a stick of incense and hold it where the unit and the window frame meet; for central AC, hold the stick near duct connections. If the smoke blows around, you’ve got leakage. For ductwork, use foil tape to seal small gaps and duct mastic for larger ones; for window AC units, stuff foam between the device and the window frame, taping as needed.
 
3. Use a timer
 

Why and How to Use a Timer

There’s no need to blast the AC at full tilt while you’re at work. For central units, install a programmable thermostat that lets you set higher temps when you’re gone and cooler temps when you’re home. Newer window units have built-in timers and adjustable thermostats, or you can buy a timer at any home store for $10 to $20; just make sure it matches your device’s voltage. Unless you’re going on vacation, don’t shut off the system; otherwise, the air compressor will need to work harder to cool your house later.
 
4. Insulate, Insulate, Insulate
 

Why and How

Ducts in hot attics or crawl spaces should be wrapped to keep the air within them cool. You can use spray foam, batt insulation, or rigid-foam insulation. Seal batt and rigid insulation with foil tape (not duct tape). For tight spaces, wraps like Reflectix offer some degree of insulation.
 
 
5. Keep the compressor and condenser free of obstruction
 
Why and How to Service Compressor/Condenser
 
A central AC system’s air compressor and condenser are usually located outside the house, close to your foundation. It works best when there’s about 24 inches of clear space in all directions, so get rid of nearby shrubs, tall grass, leaves, and hanging branches.
 
6. Don’t make it so hard
 
Why and How to Keep Unit Cool
 
Extend the life of your AC system by keeping blinds or shades down during the day; you can also install awnings to shield south-facing windows from intense sun. Consider running the AC in conjunction with floor or ceiling fans to circulate cooled air more effectively.
 
7.  Get somebody on the maintenance
 

Why and How to Maintain Unit

The dealer who installed your central AC (or one you find locally) should put you on a yearly cleaning schedule that goes beyond just cleaning the filters. Schedule this checkup before the cooling season starts (or do it now if you didn’t do it earlier this year), and make sure it includes the following tasks: cleaning and inspecting coils; cleaning or replacing filters; adjusting and replacing fan belts; lubricating motors and bearings; cleaning and checking blowers and fans; inspecting controls and safeties; checking refrigerant and pressures; and verifying operating temperatures.
8. Don’t close off rooms

Why and How to Get Airflow

Shutting too many interior doors causes central AC systems to go out of balance, meaning there’s less airflow in the entire house. If you want some privacy, keep doors slightly ajar instead.
 
9. Consider an upgrade
 

Why and How to Upgrade

Federal laws require AC units to be a lot more efficient than they were just 10 years ago. For central AC, look for the seasonal energy-efficiency ratio, or SEER; for window units, the measure is simply called the energy-efficiency ratio, or EER. The standards mandate a SEER of 13 and an EER of 8, but devices with higher numbers will cost less to operate.  -This old house
 
2016-03-14T16:57:35+00:00